Evaluation of test methods used to characterize fiber reinforced cementitious composites

Ieva Paegle, Gregor Fischer

Abstract


This paper describes an investigation of fiber reinforced cementitious composites in terms of their behavior under tensile and flexural loading. Flexural testing and subsequent derivation of the tensile stress-deformation response from the flexural test data are preferred in the assessment of the tensile properties of Fiber Reinforced Cement Composites (FRCC) over the direct measurement of the tensile behavior because of the more convenient test setup and ease of specimen preparation. Three and four-point bending tests and round determinate panel test were carried out to evaluate the flexural response of FRCC. The assumptions made in the inverse analysis on the formation of cracking suggested in many standardized evaluation methods and established correlation methods have a strong influence on the results of the conversion from flexure to tension. In this paper, the formation of cracking and crack development have been quantitatively documented using a digital image correlation (DIC) system to investigate the validity of the commonly made assumptions.

Keywords:

FRCC, standard testing, flexural testing, direct tension, DIC

Full Text:

PDF

References


ASTM C1550-10. Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel), 2012.

ASTM C1609/C1609M-12. Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading), 2012.

ASTM C39/C39M-12a. Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, 2012.

ASTM C496/C496M-11. Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens, 2011.

BS EN 12390-3:2009. Testing hardened concrete. Compressive strength of test specimens, 2009.

BS EN 12390-6:2009. Testing hardened concrete. Tensile splitting strength of test specimens, 2009.

DBV-Guide to Good Practice. Steel Fibre Concrete. Editor: German Society for Concrete and Construction Technology, DBV, Berlin, 2001/2007.

DS EN 14651 + A1:2007. Test method for metallic fibre concrete - Measuring the flexural tensile strength (limit of proportionality (LOP), residual), 2007.

Fischer, G.; Stang, H. and Dick-Nielsen, L. 2007. Initiation and development of cracking in ECC materials: Experimental observations and modeling. In Proceedings of the 6th International Conference on Fracture Mechanics of Concrete and Concrete Structures, 3: 1517-1522.

ISO 1920-10:2010(E). Testing of concrete. Part 10: Determination of static modulus of elasticity in compression, 2010.

JCI-S-002-2003. Method of test for load-displacement curve of fiber reinforced concrete by use of notched beam, Japan Concrete Institute Standard, 2003.

JCI-S-003-2007. Method of test for bending moment – curvature of FRCC, Japan Concrete Institute Standard, 2007.

Johansen, K.W., 1962. Yield line theory, Cement and concrete association, London.

Li, V.C., Kanda, T. 1998. Engineered Cementitious Composites for structural applications. Journal of Materials in Civil Engineering, 10, pp. 66-69. http://dx.doi.org/10.1061/(ASCE)0899-1561(1998)10:2(66)

Minelli, F.; Plizzari, G.A., 2011. New Round Panel Test for the Characterization of Fiber Reinforced Concrete: A Broad Experimental Study. Journal of testing and evaluation, 39, pp. 889-897.

Miyazato, S.; Hiraishi, Y., 2005. Transport Properties and Steel Corrosion in Ductile Fiber Reinforced Cement Composites. In Proceedings of the 11th International Conference on Fracture. Curran Associates, pp. 1500-1505.

Pease, B.J.; Geiker, M.R.; Stang, H.; Weiss, W.J., 2006. Photo-grammetric Assessment of Flexure Induced Cracking of Reinforced Concrete Beams under Service Loads. In Proc. of the 2nd Int. RILEM Symposium, Advances in Concrete through Science and Engineering, Québec City, Canada.

Pereira, E.; Fischer, G.; Barros, J. A.; Lepech, M., 2010. Crack formation and tensile stress-crack opening behavior of Fiber Reinforced Cementitious Composites (FRCC). In Proc. Of 7th Int. Conf. on Fracture Mechanics of Concrete and Concrete Structures (FraMCoS 7), pp. 1639-1647.

RILEM TC 162-TDF: Vandewalle, L. et.al., 2002. Test and design methods for steel fibre reinforced concrete – Bending test, Materials and Structures, RILEM Publications, 35, pp. 579-582.




DOI: 10.7250/iscconstrs.2014.20

Refbacks

  • There are currently no refbacks.